cnc machine electronics and accessories
Electronics
Showing 1–48 of 131 results
- Limit Switches & Prox Sensors
10Pack Roller Lever Micro Limit Switch
Product Details:
Designed to control the movement of a mechanical part. High precision mechanism design offering acute operation and long life. The Micro Switch is widely used in appliance, electronic equipment, automatic machine, car electric, etc.
SKU: 50270 - Limit Switches & Prox Sensors
10Pk Uxcell Miniature Micro Limit Switch Snap Action
- 3 terminals, also
- Applicable to AC control circuits
- Control the movement of a mechanical part
- Automatically monitor / indicate
- High precision mechanism design
- Offering acute operation and long life
- In snap action contacts, also
- Movement of the actuator applies force to an over center mechanism
- Reversing the motion of the actuator to a given reset point causes the contacts to snap back to their original position
- Snap action contacts have different trip and reset points, also
- Finite travel to reset helps to avoid multiple changes of state if the object actuating the switch is subject to vibration
- So snap action contacts ensure repeatable performance in applications that involve low speed actuators
- The amount of travel of the contacts is also not dependent on the amount of travel by the actuator
SKU: 50556 - Power Supplies
110VAC 12VDC Universal Reg Switch Power Supply
- QUANS 12V DC 10A 120W Universal Switching Power Supply
- High quality! Low Heat, No annoying noise! IN-DOOR USE ONLY!
- No installation instruction, wiring cable, on/off switch, or screws come with.
- Please DO NOT let the unit work long hours over rated current! Normally it is better to work under 80% of rated current.
- Used in Industrial automation, LED Strips, CCTV, LED display, Communications, etc.
SKU: 50577 - Motors
12V DC Motor 201RPM with Encoder
- Rated Voltage: 12V DC constant between motor terminals
- Direction of Rotation: CW when viewed from output shaft side
- Operating Temperature and Humidity: Temperature range of -10 °C ~+50 °C, Humidity range of 30%~80%
- Storage Temperature: Temperature range of -20°C~+60°C
SKU: 50114 - Drivers & Controllers
12V to 24V Single Axis CNC Stepper Driver Controller
- All usage marked on the board, no instructions required
- Japan-imported chip Toshiba TB6560
- With large heat sink to ensure good heat dissipation
- Input signal high-speed optocoupler isolation, guarantee not losing steps
- Semi-flow mode adjustable, semi-flow current adjustable, not the general design on the market, with a variety of semi-flow model and semi-flow current setting function
- Attenuation model adjusted for all the motors can be locked when no noise
- Ultra-small, the overall size: 62mm * 75mm, installation of four mechanical positioning hole size: 65mm * 55, hole size Φ3mm
- The form of stud-type connectors and an optional plug-in
SKU: 50068 - Electrical Accessories
140 Piece Electrical Assortment Kit
- Package includes: fully male insulated spade and T-Tap quick splice wire crimp terminals connectors
- Package quantity: 140pcs
- Wire range: 22-16 ( red ) / 16-14 ( blue ) / 12-10 ( yellow ) A.W.G
- Selection of – quality copper and PVC materials processing
SKU: 50105 - Cables
15ft DB25 Male to Female Parallel Cable
Product Details:
- FEATURES: Total Length: 5M/16.4 Feet,Color: Beige, MATERIALS: ABS & CJS, RoHS Compliant;
- APPLICATION: Connect your printer,Extend your RS-232 serial or parallel cable;
- CONNECTOR: Connector 1: DB25 Male and Connector 2: DB25 Female;
- HIGH QUALITY: Each cable is foil shielded for EMI/RFI protection;Seventeen pair wire twisted with at least 36 turns per meter, molded connectors, foil shielding and 85% coverage braid soldered 360 to the connector shell all provide maximum resistance against harmful EMI/RFI, and help you to achieve the maximum performance from your peripheral.
SKU: 50403 - Cables
15ft DB25 Male to Male Parallel Cable
Product Details:
- UL Certified, RoHS Compliant
- Connector 1: DB25 Male and Connector 2: DB25 Male
- Connect your printer, modem or other RS-232 serial/parallel device to a switchbox
- Each cable is foil shielded for EMI/RFI protection
- Seventeen pair wire twisted with at least 36 turns per meter, molded connectors, foil shielding and 85% coverage braid soldered 360° to the connector shell all provide maximum resistance against harmful EMI/RFI, and help you to achieve the maximum performance from your peripheral.
SKU: 50406 - Cables
25ft DB25 Male to Female Parallel Cable
Product Details:
- Easily extend your existing cables at a lower cost than buying a new cable. All 25 lines are wired straight through pin-to-pin for ease of compatibility. Each cable is foil shielded for EMI/RFI protection, and is available fully molded with thumbscrew connectors for a fast, easy connection every time.
- Connector 1: (1) DB25 Male, Connector 2: (1) DB25 Female
- Extend your RS-232 serial or parallel cable
SKU: 50404 - Drivers & Controllers
3 Axis Stepper Motor Driver CNC TB6600 Board Kit
This complete kit is typically for automation equipment DIYs.
- Offers four different kits with different interface controller board to satisfy various needs.
- Comes with easy-to-assemble basic parts for you to make your own machine.
- The TB6600 3-Axis Stepper Motor Driver Board is using TOSHIBA TB6600 HG driver chip and it can effectively drive 3 motors at the same time.
SKU: 50111 - Limit Switches & Prox Sensors
3 pcs ME-8108 Momentary Limit Switch
- Actuator Type : Rotary Adjustable Lever Arm with Roller
- Actuator Action : Momentary
- Advantage: Double reed mechanism ensuring longer mechanical life
- Material: Zinc alloy and reinforced plastic
- Features: Double circuit limit switch
SKU: 50555 - Drivers & Controllers
3A Single Axis CNC Router Stepper Motor Driver Board
The TB6560 single-motor driver board is based on TB6560AHQ chip. It will significantly increase torque and ease of configuration of larger motors. Cheap and great driver for CNC or 3D printer
- the current level adjustable to meet your various application needs.
- the Automatic half-decay adjustable.
- 6N137 high-speed optical coupling, to ensure a high speed not step out.
- thick tooth radiators, good heat dissipation.
SKU: 50071 - Cables
3ft DB25 Male to Female Parallel Cable
Product Details:
- UL Certified, RoHS Compliant
- Connector 1: DB25 Male and Connector 2: DB25 Male
- Connect your printer, modem or other RS-232 serial/parallel device to a switchbox
- Each cable is foil shielded for EMI/RFI protection
- Molded connectors, foil shielding and 85% coverage braid soldered 360° to the connector shell
- All provide maximum resistance against harmful EMI/RFI, and help you to achieve the maximum performance
SKU: 50405